wholesale metal jewelry
5 thoughts on “wholesale metal jewelry How to use red rope to make good -looking necklaces?”
Leave a Comment
You must be logged in to post a comment.
Ready to get answers from a qualified injury lawyer?
Malesuada dignissim non, aliquam id tincidunt amet in sed et gravida pulvinar ipsum mauris etiam mattis nisl.
wholesale recycled cardboard jewelry boxes As shown in the figure, a red rope is worn outside the other green rope
repeated the red rope steps, and you can put on the green rope like to tighten it to wear your favorite beads on the side of the rope. This is the same way to edit the same way, and a beautiful red rope necklace is compiled.
925 express wholesale jewelry 常 King Kong knot is a common amulet. Red rope bracelet is a common weaving bracelet. The red rope King Kong bracelet combines the decoration and guardianship function into one. It is currently the most popular weaving bracelet. Choose a red rope and the corresponding pendant. If you do n’t need a pendant, you can use only red rope. Each bracelet is about 160cm; fold the red rope to start with the flower type, evenly tighten, leave a small hole as a buckle; The second King Kong knot follows the last start, the cross is as shown in the figure, tightened into the second knot, puts the second line in the cross, and prepares the third King Kong knot; tighten the completion. At that time, wear accessories, and then continue to compile the other half of the King Kong knot; turn the red ropes below around the double ring, then put into the middle square hole, and turn the other tail into the same square hole. Gently pull up the three -dimensional shape, adjust and tighten. Subtract the excess red rope, stick to the tail with glue, and complete. Bleak
jewelry storage boxes wholesale ， Plade the diamond knot, clamp it with a small clip (my tips), and take the two ends of the two ends of the Diamond knot. It should not be too tight. Then turn a red rope into a double line, hold one with a double red rope with one hand, control the curved end of the one hand, and then entangle the two red ropes. Pay attention to controlling the tightness. After a certain length, do the knot and pay attention to the control of the length. At this time, you can combine the two ropes to the holes that pass through the transshipment ball to string it up. The second transshipment bead, use the repeated method to connect the transshipment bead you prepared, and then repeat the cross -wound movement until the length of the wrist with the wearer can be knotted. Finally, cut the remaining red rope with scissors after the knot, and then burn the wire head with a lighter to play a fixed role. Bleak
pet themed jewelry wholesale 居 Take two of them, from the middle of the left, do King Kong knot, and look at the eyes. My skills of doing the diamond knot lies in the winding line, and the edited part is placed on the belly of the fingers. Every time, keep it like this, and the edited King Kong knot will be neat. Diamond knot is about 2 cm. Take the other two red ropes, and the center is on the line of King Kong.
It set up four braids after setting up. My skills of making four braids are, one -handed, pinch the edited part with my left hand, and cross the two lines on the opposite side of the right hand. It was edited, because the bracelet I compiled was 17cm, so the entire rope was compiled to 17cm, and a single buckle was temporarily fixed. In the same way, the last two red ropes were set on the other side of King Kong and made four braids. For the folding King Kong knot, clamp it with a small clip (my tips), take one of the two ends of the threading line of King Kong knot, and it should not be too tight. Bleak
wholesale sterling steel jewelry 根 Preparation before editing: two ropes, three bracelets and two tranquil beads. Find a rope, fold it, compile a dual connection, do not tighten. In addition, take a rope, fold it, plug into the knot, and tighten the knot. The two ropes in the middle are edited twice. Replace the two ropes next to the middle, pay attention to replace one from below, and change from top. The two ropes in the middle are edited twice. In the future, repeat step 4 and strings on the transshipment beads on the rope. Edge in sufficient length, compile the two ropes on the side into a dual connection, plug the middle two into the knot, cut off the two excess line heads in the middle, then make a button knot, cut off the remaining line, use a lighter or match to burn it with a lighter or match. , Make the rope more strong. Bleak